-
- Tổng tiền thanh toán:
Đang cập nhật
Bảo hành 12 tháng
Giá chưa bao gồm VAT
Nhập NYAUDIO777 Nhận ngay ưu đãi Freeship (tối đa 200.000đ) khi thanh toán bằng VNPAY-QR hoặc chuyển khoản trên ứng dụng ngân hàng với đơn hàng từ 2.000.000đ. Tìm hiểu thêm
Almost 50 years after Mr. Rupert Neve created his first diode bridge compressor designs, the 535 reimagines the larger-than-life personality of these classic circuits with new levels of precision and adaptability, helping virtually any track shine through a mix.
A 31-position detented pot that sets the level at which compression begins, from -25dB to +20dB. Turning this control counter-clockwise will increase the amount of compression; turning it clockwise will decrease the amount of compression.
The RATIO control has six selectable positions on a rotary switch, allowing the user to set the slope of the compressor curve with pre-selected ratios of 1.5:1 through 8:1 for levels above the determined THRESHOLD. This range of compression ratios allows the user to compress as moderately or heavily as desired.
The TIMING control is a six-position rotary switch that sets the compressor attack and release times. The timing can be further modified by the FAST button.
FAST – Fast Attack (750us), Fast Release (130ms)
MF – Medium Attack (2.25ms), Fast Release (130ms)
MED – Medium Attack (2.25ms), Medium Release (400ms)
MS – Medium Attack (4ms), Slow Release (725ms)
SLOW – Slow Attack (10ms), Slow Release (1S)
AUTO – Medium Attack (5ms), Dual Decay Release (T1 500ms, T2 1s)
The FAST switch divides the attack and release times available on the TIMING control in half, effectively doubling the number of TIMING presets available to the user.
The BLEND control has 31 detents and allows the user to mix the uncompressed (dry) signal with compressed (wet) signal. Turning the control towards 0% will shift the mix to fully uncompressed dry signal, whereas turning the control towards 100% will shift the mix to the fully compressed signal. This feature allows for parallel compression, enabling a wider range of compression subtlety.
The GAIN control has 31 detents and allows the user to add make-up gain to the compressed signal in order to bring its level back up to unity with the uncompressed input signal. It is much easier to evaluate the tonal effect of the compressor (via the COMP IN switch) when the compressed output level is matched to the uncompressed input level, thereby eliminating potentially misleading level differences.
The COMP IN switch allows the user to audition the compression. By disengaging the COMP IN switch, the compressor is bypassed and the user can quickly compare the compressed sound to the dry input signal for an objective evaluation of the compressor’s sonic effect on the audio signal. COMP IN can be used in combination with the GAIN control to match the perceived level of the compressed audio signal with the level of the uncompressed input signal.
The LINK switch allows the compressor to be linked to another 535 compressor module via a sidechain control voltage. In link mode, the compressor generating the greater sidechain voltage (resulting in higher amounts of compression) will control the compression of both audio signal paths to maintain proper stereo center image while compressing. Note: it is advisable to always audition the unlinked sound as well, to decide if the benefit of a constant stereo center image is worth the potential trade-off of reduced left / right independence in the stereo field.
The S/C HPF switch allows the user to insert a 12dB/octave 150Hz high-pass filter in the compressor sidechain. When this filter is engaged, the compressor will be considerably less responsive to information below 150Hz. For example: if used on a drum kit, the low end of the kick drum would have less proportional effect on the compression than a snare drum or cymbals, since a significant portion of the kick drum’s dynamic energy is focused below 150Hz.
These two LED meters provide accurate representations of both the output level of the compressor and the amount of gain reduction being applied to the input signal.
By @nyaudio
Để tiện lợi trong việc mua hàng, chúng tôi khuyến khích quý khách đặt hàng online đơn giản và tiện lợi. Sau khi đặt hàng chúng tôi sẽ chủ động liên hệ tư vấn về sản phẩm và Chính sách vận chuyển.
1. Chọn Sản Phẩm
Khách hàng lựa chọn sản phẩm cần đặt. Bấm vào nút THÊM VÀO GIỎ
2. Xác Nhận
Sản phẩm đã lựa chọn sẽ được cho vào ngay giỏ hàng. Tại đây, khách hàng có thể tiếp tục đặt mua thêm sản phẩm khác hoặc thêm số lượng cho sản phẩm vừa chọn! Nếu không lựa chọn thêm sản phẩm nào nữa, vui lòng bấm vào nút "THANH TOÁN"
3. Hoàn Thành Đơn Hàng
Tại đây, Khách hàng chỉ cần điền tên, số điện thoại liên hệ, và địa chỉ nhận hàng,các hình thức thanh toán có thể thanh toán Online,chuyển khoản hoặc COD click vào phương thức bạn muốn thanh toán,sau đó đặt hàng hoàn thành nhân viên của chúng tôi sẽ gọi điện lại cho khách hàng, tư vấn - xác nhận và gửi hàng,Thời gian nhận hàng từ 1 đến 3 ngày tùy địa phương.